Enc ENC28J60 Sizes for Use On V500+ Expansionport | |
---|
|
---|
| | Mo Retro
Posts 241 26 Mar 2018 00:56
| In the expansionport HowTo they use this module EXTERNAL LINK Was wondering if the smaller one is also a good choice:https://i.ebayimg.com/images/g/A5YAAOSwT5tWKuQ~/s-l500.jpg
| |
| | Matthew Langtry
Posts 199 26 Mar 2018 07:16
| Should work, I had one but was missing a and capacitor. So didn't work correctly. The pin out will be slightly different on the silkscreen.
| |
| | Eric Gus
Posts 477 27 Mar 2018 07:41
| I guess the key thing here is be sure you get a 3.3v module.. (thanks to Lenny Rivera on FB for pointing this out to me) the ones commonly used for the SDNET are the 5v flavor.. not recommended to run on the expansion port.. EXTERNAL LINK
| |
| | Robert MyAmigaShop
Posts 3 27 Mar 2018 11:06
| What does "Pullup 50k" mean in the remarks?
| |
| | Chris Dennett
Posts 67 27 Mar 2018 11:46
| I am using the smaller one, so yes, it works. Make sure it is 3.3V. I wonder if actually the larger ones are the 5V ones.
| |
| | Gunnar von Boehn (Apollo Team Member) Posts 6214 27 Mar 2018 12:02
| always use 3.3 V - never use 5V modules!
| |
| | Mo Retro
Posts 241 27 Mar 2018 12:07
| Thanks for the answers guys. I've ordered the ones in the expansion port FAQ.
| |
| | Andy Hearn
Posts 374 28 Mar 2018 20:33
| ok, i have the gold2.8x11 core and coffin r49 on a 500v2+. a 3.3v Ethernet module. followed the pin out guide from the exp port to the module installed SAGA1.2 downloaded the v2expeth.device_1.2.lha and got that into my A500 extracted and have v2expeth.device in devs:networks size 10,984 bytesremoved roadshow and installed genesis. controversial I know, but it works without any demo limits. setup everything in Genesis - static IP's, netmask, default gateway, ip address, hostname... but when I try to go online, it just sits at initializing device. I am able to cancel and try again, but if I follow the wizard to do the setup, it tries to do a BOOTP and just sits there without doing anything. anything obvious that i'm missing?
| |
| | Eric Gus
Posts 477 28 Mar 2018 20:38
| Andy Hearn wrote:
| ok, i have the gold2.8x11 core and coffin r49 on a 500v2+. a 3.3v Ethernet module. followed the pin out guide from the exp port to the module installed SAGA1.2 downloaded the v2expeth.device_1.2.lha and got that into my A500 extracted and have v2expeth.device in devs:networks size 10,984 bytes removed roadshow and installed genesis. controversial I know, but it works without any demo limits. setup everything in Genesis - static IP's, netmask, default gateway, ip address, hostname... but when I try to go online, it just sits at initializing device. I am able to cancel and try again, but if I follow the wizard to do the setup, it tries to do a BOOTP and just sits there without doing anything. anything obvious that i'm missing?
|
Core 2.9 perhaps? I dont think its out yet.
| |
| | Andy Hearn
Posts 374 28 Mar 2018 21:04
| woopsy! ignore me. I had CS and s0 round the wrong way ok so I have flashy lights. a red light on the eth module, and link and activity lights on the network port. just the same "initializing device" if I try to go online and a stuck BOOTP if I try to configure using the wizard oh, and performance is crippled (comparatively). as soon as i unplug everything from the exp port, and power back on, all is well speed wise ok so i pulled all the wires and plugged them all back in again. no performance problems anymore, but still the IP stack not initialising the device. it must be me doing something stupid.
| |
| | Shane Stringer
Posts 22 28 Mar 2018 22:07
| From the instructions on the Wiki: Documented pinout is for GOLD2.9 and upwards only. Do NOT use it on earlier cores.If you have 2.9, please share :) AFAIK it hasn't been released yet.
| |
| | Andy Hearn
Posts 374 29 Mar 2018 13:33
| i did double check on the Wiki that 2.8 enabled the expansion port, and that how to connect a ... oh my god it's there on the second line 2.9 only. *facepalm*. like i said, long day. tired....
| |
| | Hans-Georg Winkler
Posts 29 30 Mar 2018 18:45
| Jup, 2.9 I was miss guided in the same way ;-) so we have to wait until it's out...
| |
|